| GT2510-VTBA |
| GT25 model |
| GOT2000 |
| GT25 |
| TFT color LCD |
| |
| VGA: 640 x 480 dots |
| 211.2 (W) x 158.4 (H) mm
(8.31 (W) x 6.24 (H) inch) |
| 16-dot standard font: 40 characters x 30 lines (two-byte characters)
12-dot standard font: 53 characters x 40 lines (two-byte characters) |
| 65536 colors |
| 32 levels |
| 4096 |
| LED (not replaceable) |
| Approx. 60000 h (operating ambient temperature: 25°C, display intensity: 50%) |
| White |
| Analog resistive film |
| Minimum 2 x 2 dots*9 (per key) |
| Not available*5 (Only 1 point can be touched.) |
| 1 million touches or more (operating force: 0.98 N or less) |
| Black |
| － |
| － |
| Memory for storage (ROM) *12 : 32 MB
Memory for operation (RAM) : 80 MB |
| 100000 times |
| ±90 seconds/month (ambient temperature: 25°C) |
| GT11-50BAT lithium battery |
| SRAM data, clock data, system status log data |
| Approx. 5 years (ambient temperature: 25°C) |
| 1 channel |
| 115200, 57600, 38400, 19200, 9600, 4800 bps |
| D-sub 9-pin (male) |
| 1 channel |
| 115200, 57600, 38400, 19200, 9600, 4800 bps |
| D-sub 9-pin (female) |
| － |
| － |
| － |
| － |
| － |
| － |
| － |
| 1 channel |
| 100BASE-TX, 10BASE-T |
| RJ-45 (modular jack) |
| － |
| － |
| － |
| － |
| 2 channels (front face, rear face) |
| High-Speed 480 Mbps |
| USB-A |
| 1 channel (front face) |
| High-Speed 480 Mbps |
| USB Mini-B |
| 1 channel, SDHC compliant (maximum 32 GB) |
| － |
| － |
| － |
| － |
| For installing a communication unit or an option unit |
| For installing a communication unit |
| － |
| Single tone (tone and tone length adjustable) |
| 2 colors (blue and orange) |
| Standard |
| Front: IP67F*7*10
Inside control panel: IP2X |
| 303 (W) x 218 (H) x 52 (D) mm
(11.93 (W) x 8.58 (H) x 2.05 (D) inch) |
| 289 (W) x 200 (H) mm
(11.38 (W) x 7.87 (H) inch) |
| 2.1 kg
(4.6 lb) |
| 0°C to 55°C |
| -20°C to 60°C |
| 10% RH to 90% RH, non-condensing |
| 10% RH to 90% RH, non-condensing |
| Compliant with JIS B 3502 and IEC 61131-2 |
|
Half amplitude: 3.5 mm
Sweep count: 10 times in each X, Y, or Z direction
Acceleration: 9.8 m/s2
Sweep count: 10 times in each X, Y, or Z direction
|
|
Half amplitude: 1.75 mm
Acceleration: 4.9 m/s2
|
| Compliant with JIS B 3502 and IEC 61131-2 (147 m/s2 (15 G), 3 times in each X, Y, or Z direction) |
| No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage) |
| 2000 m or less |
| Inside control panel |
| II or less |
| 2 or less |
| Self-cooling |
| Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a cross-sectional area of 2 mm2 or more. If impossible, connect the ground cable to the control panel. |
| Includes the temperature inside the enclosure of the control panel to which the GOT is installed. |
| When any of the following units or option is mounted, the maximum operating ambient temperature must be 5°C lower than the one described in the general specifications: MELSECNET/H communication unit (GT15-J71LP23-25, GT15-J71BR13), CC-Link communication unit (GT15-J61BT13), protective cover for oil. |
| When GT2505-VTBD is installed vertically, the operating ambient temperature must be between 0°C and 50°C. |
| If the ambient temperature of GT2505-VTBD exceeds 40°C, the absolute humidity must not exceed 90% RH at 40°C. |
| If the ambient temperature of GT2505-VTBD exceeds 40°C, the absolute humidity must not exceed 90% RH at 40°C. |
| Some models have ANSI/ISA 12.12.01 approval for use in Class I, Division 2 (ANSI/ISA 12.12.01, C22.2 No.213-M1987) hazardous locations.
For applicable GOT models, please refer to the Mitsubishi Electric Factory Automation Global website (www.MitsubishiElectric.com/fa/). |
| Do not use or store the GOT under a pressure higher than the atmospheric pressure at altitude 0 m.
Doing so may cause a malfunction. Air purging by applying pressure to the control panel may create clearance between the surface sheet and the touch panel. This may cause the touch panel to be not sensitive enough or the sheet to come off. |
| This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises.
Category II applies to equipment that is supplied with power from fixed facilities. The withstand surge voltage for the equipment with the rated voltage up to 300 V is 2500 V. |
| This indicates the occurrence rate of conductive material in an environment where a device is used.
Pollution degree 2 indicates an environment where only non-conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions. |
| 100 V AC to 240 V AC (+10%, -15%) |
| 50 Hz/60 Hz (±5%) |
| 80 VA |
| 34 W or less |
| 12 W |
| 7 W |
| 60 A or less
(2 ms, ambient temperature: 25°C, under the maximum load) |
| 20 ms or less (100 V AC or more) |
| Noise voltage: 1500 Vp-p, noise width: 1 μs,
measured by a noise simulator with noise frequency ranging from 25 Hz to 60 Hz |
| 1500 V AC for 1 minute across power terminals and earth |
| 500 V DC across power terminals and earth, 10 MΩ or more by an insulation resistance tester |
| 0.75 mm2 to 2 mm2 |
| Solderless terminal for M3 screw RAV1.25-3, V2-S3.3, V2-N3A, FV2-N3A |
| 0.5 N・m to 0.8 N・m |
